Toothpick Electronics

AMAXinno 1103 – 7500KV
AMAXinno 1103 – 7500KV
Specification:
Brand name: AMAXinno
Item name: 1103 Brushless Motor
KV: 7500
Lipo Cell: 1-2S Max.100W / 12,5A @8V
Magnets: N52H
Cable: 8.5cm
Weight: 3.8g
Features:
Super Power & Efficiency
Minimum Air Gap between Stator & Magnets
Balance checked with Betaflight
Package Includes:
1 x 1103 Brushless Motor
2 x M2*7mm Screws
3 x M2*5mm Screws
AMAXinno Motor Bearings
AMAXinno Motor C-clips
BETA – F405 2-4S AIO Brushless Flight Controller (BLHeli_S) V3
Specifications of F405 12A AIO FC V3
- CPU: STM32F405RGT6
- Six-Axis: MPU6000
- Size: 26mm x 26mm
- Firmware version: Batefight-BETAFPV405-4.2.X
- OSD: Built in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
- Receiver: Support Frsky XM/XM+FCC Receiver/ Futaba Receiver/ Flysky Receiver/ TBS Crossfire Receiver/DSMX Receiver
- Weight: 5.3g
- Connecter: XT30
Specifications of ESC
- Support PWM,Oneshot125,Oneshot42, Multishot,Dshot150,Dshot300,Dshot600
- Input voltage: 2S-4S Lipo
- Continuous current: 12A
- Peak current: 13A
- Firmware: BLHELI-S G-H-25
BETA – Toothpick F722 2-6S AIO Brushless Flight Controller 35A(BLHeli_32)
Specification of FC
- Item: F722 35A AIO FC(BLHeli_32)
- Weight: 7.89g
- CPU: STM32F722RET6
- Six-Axis: MPU6000 (SPI connection)
- Mounting hole size: 26mm * 26mm
- Firmware version: betaflight_4.2.x_BETAFPVF722
- OSD: Built-in BetaFlight OSD (OSD chip: AT7456E)
- Support programmable LED like WS2812 etc
- Built-in current sensor
Specification of ESC
- Signal support: PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600
- Receiver: Support Frsky XM/XM+ Receiver/ Futaba Receiver/Flysky Receiver/DSMX Receiver/TBS Crossfire Receiver (requires external connection)
- Input voltage: 2S-6S Lipo
- Continuous current: 35A
- Peak current: 40A
- ESC firmware: BLHELI_S 32
- Indicators: 2 indicators: receiver indicator (green)/Flight control power indicator (red)
- Capacitance: CS|5*10*13mm|470μF|35V
- Connecter: 80mm 14AWG silicone cable with XT60
- Recommended motors: 14XX series, 15XX series, 16XX series, 18XX series, 20XX series
BETA 1105-5000KV Brushless Motors (4PCS) for Beta 85X
SPECIFICATION
- Height: 14mm
- Weight: about 5.2g (1 pc)
- Shaft: φ1.5mm
- Motor Mount Holes: M2.0 on Dia 9.0mm
- KV (rpm/V): 5000 – UP TO 4S
- Plug and cables:
- Micro JST-1.25 3-pin connector with 28AWG cables (5000KV)
BETA 1204 5000KV Brushless Motors (4pcs)
BETA 1204 5000KV Brushless Motors (4pcs)
1204 5000KV motor is one of the best motors for 2-3inch FPV Racing Drone, which has increased power efficiency, adopting multi-heat dissipation hole design helps to pull heat away continuously in flight. Super durable and ultra-light unibody bell shape with only 5.9g. The sturdy structure and high-quality materials make it performs like a beast, you”ll have your mind blown!
SPECIFICATION
- Height: 15.4mm
- Weight: 5.9g (1 pcs)
- Shaft: φ1.5mm
- Motor Mount Holes: M2EQS on Dia 5.0mm
- KV (rpm/V): 5000
- Input Voltage: 3-4S LIPO
- Plug and cables: Micro JST-1.25 3-pin connector with 28AWG cables (5000KV)
BETA 1805-1550KV Brushless Motors(4pcs)
BETA 1805-1550KV Brushless Motors(4pcs)
Specification
- Item: 1805 brushless motor
- Motor KV (rpm/V): 2550KV, 1550KV
- Weight: 16.1g for 1pc
- Color: blue-black
- Shaft: φ1.5mm
- Shaft length: 3.8mm
- Shaft diameter: 1.5mm
- Hole distance: 12mm
- Motor Mount Holes: M2
- Input Voltage: 1550KV for 6S LIPO
- Cables: 100mm long, 24AWG cables
- Dimensions: 23.2 * 23.2 * 19.7mm
BETA Toothpick F4 2-4S AIO Brushless Flight Controller 20A(BLHeli_S) V3 Version
SPECIFICATIONS OF FC
- CPU: STM32F411CEU6 (100MHZ)
- Six-Axis: MPU6000 (SPI connection)
- Size: 32.5*32.5mm (26.5mm mounting holes)
- Firmware version: BETAFPVF411 (BEFH)
- OSD: Built-in BetaFlight OSD (OSD chip: AT7456E)
- Receiver: Support Frsky XM/XM+ Receiver/ Futaba Receiver/ Flysky Receiver/ TBS Crossfire Receiver/DSMX Receiver
- Support programmable LED like WS2812 etc
- Built-in current sensor
- Weight: 6.63g
SPECIFICATIONS OF ESC
- Support BLheli/BLHELI_S suite Pass-through ready
- Support PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600
- Input voltage: 2S-4S Lipo
- Continuous current: 20A
- Peak current: 25A
- Firmware: BLHELI_S
- Motor Connectors: 1.25mm header pins connector
BrotherHobby R3 1103 – 8000KV
BrotherHobby R3 1103 – 8000KV
Specification
- Brand Name: BrotherHobby
- Model: Returner R3 1103
- Item Name: 1103 8000KV, 1-2S Brushless Motor
- Configuration: 9N12P
- KV: 8000KV
- No.of Cells(Lipo): 1-2S
- Rotor: N52H arc magnets
- Wire AWG: 30AWG
- Stator: 0.2mm Kawasaki silicon steel
- Bearings: Japanese NSK 4X1.5X2
- Base casing: Al 7075
- Bell cap: Al7075
- Weight: 4g
BROTHERHOBBY VY 2004 KV:1950KV – SUB 250G BUILDS
BROTHERHOBBY VY 2004 KV:1950KV – SUB 250G BUILDS
SPECIFICATION
- KV: 1950KV (6S 5″triblade prop)
- Configuration: 12N14P
- Wire AWG: 24AWG 16cm
- Magnet: N52H
- Copper wire: 260 ℃ Military Grade Material
- No.of Cells(Lipo): 6S
- Base casing: Al 7075
- Bell cap: Al 7075
- Bearings: Japanese NMB 7x3x3mm
- Stator: 0.15mm Nippon stell silicon steel
- Bolt Pattern: M2 (12X12mm)
- Weight: 14.9g with short wire
Included
- 1x VY 2004 Motors
- 4x M2x6 base screw
- 2x M2x7 prop screw
Specially designed for the Ultra Lite Build (SUB 250gr /W lipo)
FPV CYCLE 1202,5 X 11500KV MTORS – 2MM SHAFT – Each
Nothing is simpler and more convenient than 1S. The trouble has been that 1S performance for anything beyond a Whoop is usually considered pretty weak with poor handling. This motor paired with the Gemfan 3016 prop and a 600mah 1S battery is the answer.
Specifications:
- ~4.3g with long, ~51mm wires and JST1.25 connector
- Mounting: 9mm diameter, 4 hole, M2
- 27awg silicone motor wire
- 2mm press fit prop shaft that’s 4mm tall
- 2mm internal shaft all the way through
- T-mount prop mounting also
- 5mm size bearings
- C-clip bell bottom and no C-clip n top
- 0.15mm laminations
- 7075 aluminum
- Single piece bell design
Included:
- 1 motor
- 2x 8mm screws for T mount props
- 4x 4mm screws for mounting motors to 2mm thick carbon frames
Recommended use:
- Low load 3” prop: Gemfan 3016 STRONGLY recommended
- Recommended all up weight (including 1S battery): 49-56g
FPV CYCLE 1S AIO WITH TBS CROSSFIRE + TBS PRO 32 NANO VTX
Specs of AIO board:
- 1S. This is a 1S board. DO NOT RUN 2S!
- We will declare 6A solid FETs but they’re 8+A capable
- Robust electronic routing so the FET’s can actually perform as intended (this is as important as the FETs here)
- No motor connectors, only solder pads
- Separate ground and volt pads for vTX, Cam and Rx
- F4 MCU preloaded with BF 4.1
- BF Target: Zeez Whoop
- 2.7g plain board weight
- 0.85mm thick PCB
- Jumpers for Rx voltage and inverted/un-inverted signal
Specs of TBS Unify Pro32 Nano:
- Operating Voltage: 3-13V
- Operating Temperature: watch for normal airflow
- Video Input Impedance: 75 Ohm
- Weight: 1g
- Dimensions: 15 x 13 x 2mm
- Antenna Connector: u.FL socket
- Video Format: NTSC/PAL
- Output Power: 14dBm (25mW), 20dBm (100mW), 26dBm (400mW), 28dBm (500+mW)
FPVCycle 1S AIO – No RX or VTX
FPVCycle 1S AIO – No RX or VTX
This board was specifically designed to provide ease of use, reliability and performance for whoop and BabyTooth style 1S builds. Because solder pads are notably more efficient and effective, we’ve ditched the connectors entirely. You’re going to appreciate how large, clearly marked and accessible these solder pads are but this is still a tiny whoop board so you’re still going to need to be pretty careful soldering. There are also separate volt and ground pads for both the Vtx and the camera so you don’t need to double up wires onto one pad. Around back you’ll find a jumper for the voltage you would like to set your Rx to and if you’re planning on going with Sbus or CRSF (inverted or un-inverted). Otherwise, the FET’s on this guy are specifically designed to handle motors around the 1202.5 range in ~10,000-12,000kv
Specs of AIO board:
- 1S. This is a 1S board. DO NOT RUN 2S!
- We will declare 6A solid FETs but they’re 8+A capable
- Robust electronic routing so the FET’s can actually perform as intended (this is as important as the FETs here)
- No motor connectors, only solder pads
- Separate ground and volt pads for vTX, Cam and Rx
- F4 MCU preloaded with BF 4.1
- BF Target: Zeez Whoop
- 2.7g plain board weight
- 0.85mm thick PCB
- Jumpers for Rx voltage and inverted/un-inverted signal
Full Speed 1106 C2 4500KV 2-4S
HGLRC FD1103 8000KV Brushless Motor
HGLRC Forward FD1103 8000KV Brushless Motor – With Connectors
Brand name: HGLRC
Item name: FD1103 8000KV Brushless Motor
Motor:KV8000
Stator Diameter:11mm
Stator Thickness:3mm
No.of Stator Arms:9S
No.of Rotor poles:12P
Motor Resistance:330mΩ
Max Continuous Current:5.46A
No.of Cells(Lipo):2-3S
ESC:6A
Recommended Prop(inch):2.5 Inch
Wire type:28AWG x 40mm
Weight:4g
HGLRC FD13A BL_S 3-6s 13A 4in1 ESC – 16 X 16
FD13A BL_S 4in1 ESC
Item Name: FD13A 4in1 3-6S ESC
Input Voltage: 3-6S Lipo
Constant Current: 13A
Peak Current: 15A(5S)
BEC Ouput: NO
Size: 23x24mm
Installing Hole: 16x16mm, M2
Weight: 3.2g
CPU: SILABS EFM8BB2 48MHZ
MOS Tube: TOP QUALITY MOSFET
Support Damped Mode:DSHOT600/300/150/Oneshot125/42,MultiShot,PWM
HGLRC FD411 3-6s Flight Controller – 16 X 16
FD411 Flight Controller
Item Name:FD411 Flight Controller
MPU: MPU6000-SPI
CPU: STM32F411CEU6
Black Box: NO
Input Voltage: 3-6S Lipo
Built-in Betaflight OSD to adjust PID
BEC Output: 5V2A
Size: 21x21mm
Installing Hole: 16x16mm, M2
Weight:2.7g
Support SBUS/PPM/DSMX/iBUS receiver
HGLRC LED ARM C232B For ESC Motors 4PCS
HGLRC LED ARM C232B For ESC Motors
Support voltage:2-6S
Color:Blue, Green or Red
Quantity:4 PCS
Overcurrent:15A
Size:13x5mm
Weight:1.2g(4 pcs)
Package Included:
4x C232B LED Light board
4x Heat shrinkable tube 5mm