This arm brace will give extra crash toughness to your frame. In addition it will help to provide a surface to bounce off race gates and flags instead of getting tangled up! Made of 4mm thick 3K matte twill weave carbon fiber. Fits only the Merica 5" (front or rear brace) or Raging Droner 5R (rear brace only) .
Water Cooling Tubing for the Spartan. FEATURES: Silicone construction, blue in color INCLUDES: One 3' length of fuel tubing SPECS: Inside diameter: .101" (2.5mm) Outside diameter: .212" (5.5mm) Length: 1m (39")
Drive Strut for the Traxxas Spartan Race Boat. FEATURES: Aluminum construction Anodized blue in color Pre-installed strut bushing INCLUDES: One drive strut
Motor Coupler Collet for the Traxxas Spartan. FEATURES: Steel construction, silver color Joins the driveshaft of the boat to the crankshaft of the engine INCLUDES: One Two-piece cable collet and two wrenches
Features: 1.Customized aluminum alloy front end to effectively protect unobstructed O3. 2.Customized silicone gel shock absorption for the O3 lens, eliminating jelly effect. 3.Customized aluminum alloy heat dissipation device at the bottom, seamlessly integrated with O3 and RunCam link transmission, while also facilitating Type-C and memory card insertion for convenient frequency adjustments. 4.Flight tower compatibility: Hole patterns for 2020mm/ 25.525.5mm/30.5*30.5mm.…
FC MCU : STM32F405 IMU(Gyro) : ICM42688P USB Port Type : Type-C Barometer : Built-in OSD Chip : AT7456E chip BLE Bluetooth : Supported WIFI : Not supported DJI Air Unit Connection Way : Direct soldering Compatible with all DJI Air Units: DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1 Blackbox : 8MB Onboard Flash Power Input : 3-6S UART :…
SPECIFICATIONS: SpeedyBee F405 V4 30x30 Flight Controller MCU STM32F405 IMU(Gyro) ICM42688P USB Port Type Type-C Barometer Built-in OSD Chip AT7456E chip BLE Bluetooth Supported. Used for Flight Controller configuration (MSP should be enabled with Baud rate 115200 on UART4) WIFI Not supported DJI Air Unit Connection Way Two ways supported: 6-pin connector or direct soldering. 6-pin DJI Air Unit Plug Supported.…
Key Features MCU: STM32F405,168MHz,1MB Flash IMU: ICM-42688-P Baro: SPL006-001 Blackbox: SD Card Number of UARTs: 6 Number of I2C: 1 ADC: 4x (VBAT, Current, RSSI, Analog Airspeed) PWM outputs: 11 (+1 LED pad) FC FW: iNAV/Ardupilot (SpeedyBeeF405WING) Input voltage: 7-36V (2-6S) Voltage sensor: 1K:10K (Scale 1100 iNav, 11.0 Ardupilot) Current sensor: 80A continuous, 150 short term (Scale 195 iNav, 50…
Specifications Power Output: 1) 10 groups of 5V output, three +5V pads and 1 BZ+ pad (used for Buzzer) on the front side, and 6 +5V output included in the connectors on the bottom side. The total current load is 2A. 2) 2 groups of 9V output, one +9V pad on the front side and the other included in a…
R2,800.00Original price was: R2,800.00.R2,500.00Current price is: R2,500.00.
Specifications Dimensions: 36.5mm(L) x 36.5mm(W) x 7mm(H), recommended for quads at 3.5" or above MountinPattern: 25.5 x 25.5mm, 3mm hole diameter Power Input: 3S - 6S Lipo Weight: 10.1g FLIGHT CONTROLLER USB Connection: Need to solder a USB TYPE-C module to D+, D-, GND pads. 5V Output: 4 groups of 5V output. The total current load is 2.5A. SmartPort: Use…
Specification Item: SPI Frsky Receiver Chip: CC2500 Weight: 0.43g Connection Way: Pin-Connector Support Protocol: Frsky D8, Futaba Dimensions: 13.5mm*9mm Recommended FC: F4 1S AIO FC, Lite 1-2S Brushless FC This SPI receiver comes with Plug & Play port, and is specially designed for the F4 1S AIO FC(No Rx) and lite 1-2S Brushless FC(NO Rx), no soldering work needed, super easy…
Opens up wide and will grip virtually every mini quad motor without scratching or damaging the bell with the built-in silicone pads. Also useful for gripping other circular shaped objects
Made out of 0.8mm Crystal clear Polycarbonate for today's low flying machines. comes with a 1mm thick wing set. Comes with a window mask and decal Also available in light weight. This V2 is ROAR approved version
50mm wide by x2 meters in length, This roll of a Aluminum tape can be used to re-enforce your bodies, or to help protect your body and fuel tank and other elements from heat damage.
Aggressive windshield design keeping front end low to the ground while rear end glued on the surface. For maximum performance, please be sure to fill in your GT8's front bumper with the anti-vibration tape to get maximum cornering speed Comes with a complete windows mask and a stylish decal sheet Wing and a set of fastner is included
2 piece of Sweep anti-vibration foam tape for receiver box, 10thth TC, 8thth GT8 body, filling up the gap between body to front bumper is a critical fix for car handling problems in On road racing. Spec: 280mm long x 23mm width 5mm thick
Sweep Racing 1/8 Vortex GT wing. Made out of 1mm poly-carbonate in stylish yet functional design. featuring built-in side dam, shark gills to maximize rear traction while 3 supporting ribs minimizing high speed vibration.
Sweep tires Formula X3 (tires traction compound for outdoor asphalt) This tire sauce is designed to provide improved traction on outdoor asphalt tracks.
R1,150.00Original price was: R1,150.00.R1,000.00Current price is: R1,000.00.
Description FRAME COMES WITHOUT THE FIN Designed in collaboration with HDZero, this frame is made to pair perfectly with the HD Race vtx v2 and the whoop size HDzero vtx. The midplate has 30×30 and 20×20 stack mounting options and the Top plate has 25.5×25.5 mounting available. Works with all Switchback PRO arms.
R800.00Original price was: R800.00.R650.00Current price is: R650.00.
T-Motor has stepped up to the plate to manufacture a second option for Spec Class racing. The AT2310 2200kV motor has been tested and refined through several renditions to ensure it matches the performance of other Spec Approved motors within just a couple points. The motor performs virtually identical to the current Spec motor and will become a mainstay throughout Spec Class…
R80.00Original price was: R80.00.R60.00Current price is: R60.00.
Replacement Motor Main Gear for T-Rex 450 - 2 Gears - no grub screws
PLEASE NOTE! We are temporarily closed due to unforeseen circumstances.
Thank you for your understanding and support during this time. Please rest assured that all current orders will be processed or refunded, and updates will be communicated as soon as possible.
